MK-8877(40T)

MK-8871(40T/2 STAGE)
MK-8870(60T/2 STAGE)

Air jack for big cars of highly efficient pneumatic hydro pump monnting type through new technology. Take a look at TongTong jack which opened a new chapter in terms of safety, economy, efficiency and convenience.

FEATURE
1. Since it is possible to operate highly efficient pneumatic hydro pump and air servo continuously for this reason this is an air jack which can be very effectively.
2. At the time of lowering after use when tie value is untied then goes down.
3. By virtue of epoch-making technology it is free form troubles.

 

SPECIFICATION

TYPE

CAPACITY

MINIMUM
HEIGHT

MAXIMUM
HEIGHT

TRAVEL
DISTANCE

SCOPE OF APPLIED
AIR PRESSURE

WEIGHT

 MK-8877

40 TON

210 mm

340 mm

210 mm

8 ~13 kg/f

40 kg

MK-8870

60 TON

180 mm

370 mm

190 mm

8 ~13 kg/f

50 kg

 


MP-5000(5T)
MP-3000(3T)

SPECIFICATION (AIR CLUTCH JACK)

TYPE

CAPACITY

MINIMUM
HEIGHT

MAXIMUM
HEIGHT

OVERALLL
ENGTH

SCOPE OF APPLIEDAIR PRESSURE

LENGTH OFHANDLE

WEIGHT

MK-3000

3 TON

120 mm

480 mm

900 mm

8 ~13 kg/f

900 mm

40 kg

MK-5000

5 TON

120 mm

520 mm

1,050 mm

8 ~13 kg/f

1,200 mm

50 kg

 

AIR FRAME JACK (FOR WORKING LOWER PART)

MR-3000/7000

MR-15000/20000

MR-22000

HOW TO USE FRAME LIFT
1. This equipment is for working on lower part of medium and large size vehicles.
2. When lifting a vehicle
    * close reversing value and slowly open forwarding value.
    * When it is raised to a proper position then make sure to install
       safety.
    * Lift up vehicle and at the time of work install safety support.
3. At the time of lowering vehicle
    * remove safety pin and open reversing value slowly.

 

SPECIFICATION

TYPE

CAPACITY

MINIMUM HEIGHT

MAXIMUM HEIGHT

MR-3000

3 TON

170 mm

700 mm

MR-7000

7 TON

265 mm

1100 mm

MR-15000

15 TON

330 mm

1250 mm

MR-20000

20 TON

330 mm

1300 mm

MR-22000

22 TON

330 mm

1300 mm

WHEEL DOLLY
MW-9000

PACK JACK
MH-2500

ENGINE LIFT (TROLLEY HYDRAULIC CRANE)
WE-8800A (3 TON)
* 180 degree rotating type for variety of cars form sedan to heavy duty vehicles

TRANSMISSION JACK

MB-8900
* For flat land
* Capacity : 1.5 TON
* Max height : 900 mm
* Min height : 370 mm

 

MB-8000
* For stand land
* Capacity : 1.5 TON
* Max height : 1670 mm
* Min height : 900 mm

 

 

PIN PRESS

FEATURE

* Power pump born form epoch making new skill
* Simple to operate
* Permanently robust equipment free from troubles
* With 10 K air press with conventional products
* Convenient air press with conventional products
* Service factory and at the time of working for lower part
* Tug rod balls for variety of cars
* Counter gear
* At the time of replacing bearings
 

FEATURE
Power source : Three phase, 220/380V, 50/60Hz
Max, Pressure : 100 TON
Stroke : 300 mm
Dimension : 850 x 1600 x ик153