WL-3000S
SCISSORS LIFT(STANDING-OUT TYPE)
SUITABLE FOR SMALL SIZE CAR CARE CENTER
 This scissors lift has been designed for repair shops and allows the user to carry out any kind of work in the utmost safety.
 As it has no post, access to hard-to-reach site is really good, and it is of course easy to work.
 Ideal model suitable for small space bay, lift capacity is up to 3,000Kg ranging small to medium size vehicles.

• Multi stage electric safety brake.
  
• Minimum installation space required.
  
• Dual packing piston(0% oil leakage)
  
• wired remote control.
  
• Optional extension for picking up van of truck.
  
• Low maintenance roller bearing.

WL-3000MS
SCISSORS LIFT(GROUND TYPE)
SUITABLE DESIGNED LIFT FOR MULTIPLE-USE
 There is no post occupying the space of work. height is adjustable for requirement.
 Panel operation with control box and remote control is available. It adopted multistage brake and stop System. as the result, various repair works with case are available here.
 Drive through ramp and strict Scissors structure provide free side installation(front and rear)

• Multi stage electric safety brake.
• Minimum installation space required.
  
• Low maintenance roller bearing.'
  
• Optional extension for picking up van of truck.
  
• wired remote control.
  
• Ready made steel case for easy in ground installation..

WL-4000TPD
TWO-POST DOOR TYPE LIFT
NEWLY RELEASED MODEL FOR THE CONVENIENCE OF WORK
 There is 4,000Kg door type lift design with overhead safe touch bar and wide between columns of inside.
 There are designed. for the purpose of safety above all. these are excellent in durability and so are Economical. repair shop owners prefer this type because of its durability and value.
 It is a medium lift with good capacity

• Two level adjustable body contact pads.
• Symmetric post for ease opening of vehicle door.
  
• Twin electronic safety dead and tin cable.
  
• Automatic arm locking device.
  
• Twin dual packing hydraulic piston for ultimate reliability.

WL-3500FP
WHEEL ALIGNMENT 4-POST JACK TYPE LIFT
EASY-TO-USE DESIGN IS FOR MULTIPLE PURPOSE
 Epochal product for transfer from an installed lift to the wheel alignment tester.
 It is fully capable of meeting the requirements of wheel alignment and routine repairing jobs and Enhanced
 Repair jobs environment. saves service time jack lift installed. on the floor and separated Work from the front And rear of vehicle possible. much safer and easily for handing than
 other products because of hydraulic Drive system. as oil pressure and electric equipment is on the post, there is no requirement of large space to install it, so, this 4-post lift is used in multiple purpose of repair works.

• Auto level looking position for wheel alignment.
  
• Perfectly free auto electrical safety locking.
  
• Hydraulic bridging jack with individual control switch.
  
• Adopted twin wire ropes.
  
• Wide width between posts offers easy entry of commercial vehicle.

WL-4000JS
SCISSORS ALIGNMENT LIFT
SUITABLE FOR THE WORKS OF WHEEL ALIGNMENT AND GENERAL USE
 Because of jack bridge with oil pressure method, it can be easily used almost all kinds of car repairs. Ease control id the benefit. Possible to use various type of alignment turntables.
 Adjustable plate for turntable height. Triple equilibrium system(torsion bar/distribution valve/balance wire) ensure strict synchronization of plate moving. Safety is guaranteed due to multi gear type
 brake system and also multi-point alignment horizontal balance is kept.

• Accomodate wide range of vehicle.(Width & height adjustable turn table)
  
• Individual control switch on each bridging jack.
  
• Lockable rear side slip plate.
  
• Heat treated grease pin & maintenance free bearing.
  
• Anti-drop valve.
  
• Pneumatic two-level jack lift.
  
• Multi-level electronic safety device.

WL-6000FP
4-POST TYPE LIFT
EASY-TO-USE DESIGN IS FOR MULTIPLE PURPOSE
 As oil pressure and electric equipment is on the post there is no requirement of large space to install it. So, this 4-post lift is used in multiple purpose of repair works. Being shorten the posts,
 it is easily installed in small space. To maximize the efficiency, the jack is attached.

• Suitable for truck and van.
  
• 5800mm long length plate
  
• Effective dual electronic device.
  
• Automatic locking device for wheel alignment balance.
• Two-wire rope
  
• Pneumatic-hydraulic two level jack(option)
  
• Drive through ramp(option)

MODEL

TYPE

CAPACITY

MAX-LIFTING HEIGHT

LIFTING TIME
(MAX HEIGHT)

LOWERST HEIGHT 

WIDTH

MOTOR SPECIFICATION          

WEIGHT

WL-3000S

SCISSORS

3,000 Kg

1,800mm

50sec

255mm

1,900mm

Single phase 2.5HP, 220V, 50/6-HZ
Three phase 2HP,220/380V,50/60HZ 

930Kg

WL-3000MS

SCISSORS

3,000 Kg

FL+1,800mm

50sec

FL-265

1,900mm

Single phase 2.5HP, 220V, 50/6-HZ
Three phase 2HP,220/380V,50/60HZ

980Kg

WL-4000TPD

2-POST

4,000 Kg

1,800mm

50sec

55mm

3,150mm

Single phase 2.5HP, 220V, 50/6-HZ Three phase 2HP,220/380V,50/60HZ|

800Kg

WL-3500FP

4-POST

MAIN 4,000Kg 

1,750mm             

55sec

184mm

3,150mm

Single phase 2.5HP, 220V, 50/6-HZ Three phase 2HP,220/380V,50/60HZ

1,400Kg

JACK 2,000Kg 

455mm

5~15sec               

820~1,550mm|

WL-4000JS

SCISSORS

MAIN 3,500Kg

1,780mm             

55sec

290mm  

2,000mm

Single phase 2.5HP, 220V, 50/6-HZ Three phase 2HP,220/380V,50/60HZ

2,250Kg

JACK 2,000Kg

455mm

5~15sec

820~1,550mm

 WL-6000FP

4-POST

MAIN 6,000Kg

1,750mm    

55sec

200mm

3,390mm

Three phase 3HP,220/380V,50/60HZ

2,300Kg

JACK 3,000Kg

455mm

5~15sec

820~1,550mm